[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, [ 1.000000] 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, [ 1.000000] 2018, 2019, 2020 The NetBSD Foundation, Inc. All rights reserved. [ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993 [ 1.000000] The Regents of the University of California. All rights reserved. [ 1.000000] NetBSD 9.2_STABLE (GENERIC) #0: Sun Oct 17 00:12:44 UTC 2021 [ 1.000000] john@frigg.zia.io:/usr/obj-sparc64/sys/arch/sparc64/compile/GENERIC [ 1.000000] total memory = 16384 MB [ 1.000000] avail memory = 16070 MB [ 1.000000] timecounter: Timecounters tick every 10.000 msec [ 1.000000] Kernelized RAIDframe activated [ 1.000000] running cgd selftest aes-xts-256 aes-xts-512 done [ 1.000000] mainbus0 (root): SUNW,Sun-Fire-V245 (Sun Fire V245): hostid 84a238ca [ 1.000000] cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1504 MHz, CPU id 0 [ 1.000000] cpu0: manuf 3e, impl 16, mask 34 [ 1.000000] cpu0: system tick frequency 20 MHz [ 1.000000] cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l) [ 1.000000] cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1504 MHz, CPU id 1 [ 1.000000] cpu1: manuf 3e, impl 16, mask 34 [ 1.000000] cpu1: system tick frequency 20 MHz [ 1.000000] cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l) [ 1.000000] memory-controller at mainbus0 not configured [ 1.000000] memory-controller at mainbus0 not configured [ 1.000000] pyro0 at mainbus0: "Fire", rev 3, ign 780, bus A 2 to 13 [ 1.000000] pyro0: pci0 at pyro0 [ 1.000000] pci0: i/o space, memory space enabled [ 1.000000] ppb0 at pci0 dev 0 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb0: PCI Express capability version 1 [ 1.000000] pci1 at ppb0 bus 3 [ 1.000000] pci1: i/o space, memory space enabled [ 1.000000] ppb1 at pci1 dev 1 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb1: PCI Express capability version 1 x4 @ 2.5GT/s [ 1.000000] pci2 at ppb1 bus 4 [ 1.000000] pci2: i/o space, memory space enabled [ 1.000000] ppb2 at pci2 dev 0 function 0: Acer Labs M5249 Hypertransport to PCI Bridge (rev. 0x00) [ 1.000000] ppb2: PCI Express capability version 1 [ 1.000000] pci3 at ppb2 bus 5 [ 1.000000] pci3: i/o space, memory space enabled [ 1.000000] ohci0 at pci3 dev 28 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03) [ 1.000000] ohci0: interrupting at ivec 780 [ 1.000000] ohci0: OHCI version 1.0, legacy support [ 1.000000] ohci0: Clear PME# now [ 1.000000] usb0 at ohci0: USB revision 1.0 [ 1.000000] ohci1 at pci3 dev 28 function 1: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03) [ 1.000000] ohci1: interrupting at ivec 780 [ 1.000000] ohci1: OHCI version 1.0, legacy support [ 1.000000] ohci1: Clear PME# now [ 1.000000] usb1 at ohci1: USB revision 1.0 [ 1.000000] ehci0 at pci3 dev 28 function 3: Acer Labs M5239 USB 2.0 Host Controller (rev. 0x01) [ 1.000000] ehci0: interrupting at ivec 781 [ 1.000000] ehci0: EHCI version 1.0 [ 1.000000] ehci0: wrong number of companions (3 != 2) [ 1.000000] ehci0: 2 companion controllers, 3 ports each: ohci0 ohci1 [ 1.000000] usb2 at ehci0: USB revision 2.0 [ 1.000000] ebus0 at pci3 dev 30 function 0: Acer Labs product 1575, revision 0x00 [ 1.000000] rtc0 at ebus0 addr 70-73: mc146818 compatible time-of-day clock: m5823 [ 1.000000] aceride0 at pci3 dev 31 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc8) [ 1.000000] aceride0: bus-master DMA support present [ 1.000000] aceride0: primary channel configured to native-PCI mode [ 1.000000] aceride0: using ivec 1f84 for native-PCI interrupt [ 1.000000] atabus0 at aceride0 channel 0 [ 1.000000] aceride0: secondary channel configured to native-PCI mode [ 1.000000] atabus1 at aceride0 channel 1 [ 1.000000] ppb3 at pci1 dev 2 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb3: PCI Express capability version 1 x4 @ 2.5GT/s [ 1.000000] pci4 at ppb3 bus 6 [ 1.000000] pci4: i/o space, memory space enabled [ 1.000000] ppb4 at pci1 dev 8 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb4: PCI Express capability version 1 x8 @ 2.5GT/s [ 1.000000] pci5 at ppb4 bus 7 [ 1.000000] pci5: i/o space, memory space enabled [ 1.000000] ppb5 at pci1 dev 9 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb5: PCI Express capability version 1 x4 @ 2.5GT/s [ 1.000000] pci6 at ppb5 bus 8 [ 1.000000] pci6: i/o space, memory space enabled [ 1.000000] ppb6 at pci6 dev 0 function 0: ServerWorks BCM5714/BCM5715 Integral PCI-E to PCI-X Bridge (rev. 0xb5) [ 1.000000] ppb6: PCI Express capability version 1 [ 1.000000] pci7 at ppb6 bus 9 [ 1.000000] pci7: i/o space, memory space enabled [ 1.000000] bge0 at pci7 dev 4 function 0: Broadcom BCM5714 Gigabit Ethernet [ 1.000000] bge0: interrupting at ivec 3795 [ 1.000000] bge0: HW config 00010115, 00000015, 00000000, 00000000 00000000 [ 1.000000] bge0: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:a2:38:ca [ 1.000000] bge0: autoconfiguration error: WARNING: failed to restrict dma range, falling back to parent bus dma range [ 1.000000] bge0: setting short Tx thresholds [ 1.000000] brgphy0 at bge0 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0 [ 1.000000] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] bge1 at pci7 dev 4 function 1: Broadcom BCM5714 Gigabit Ethernet [ 1.000000] bge1: interrupting at ivec 3796 [ 1.000000] bge1: HW config 00000114, 00000014, 00000000, 00000000 00000000 [ 1.000000] bge1: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:a2:38:cb [ 1.000000] bge1: autoconfiguration error: WARNING: failed to restrict dma range, falling back to parent bus dma range [ 1.000000] bge1: setting short Tx thresholds [ 1.000000] brgphy1 at bge1 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0 [ 1.000000] brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] ppb7 at pci7 dev 8 function 0: ServerWorks HT1000 PCI/PCI-X Bridge (rev. 0xb4) [ 1.000000] pci8 at ppb7 bus 10 [ 1.000000] pci8: i/o space, memory space enabled [ 1.000000] ppb8 at pci1 dev 10 function 0: PLX Technology product 8532 (rev. 0xba) [ 1.000000] ppb8: PCI Express capability version 1 x4 @ 2.5GT/s [ 1.000000] pci9 at ppb8 bus 11 [ 1.000000] pci9: i/o space, memory space enabled [ 1.000000] ppb9 at pci9 dev 0 function 0: ServerWorks BCM5714/BCM5715 Integral PCI-E to PCI-X Bridge (rev. 0xb5) [ 1.000000] ppb9: PCI Express capability version 1 [ 1.000000] pci10 at ppb9 bus 12 [ 1.000000] pci10: i/o space, memory space enabled [ 1.000000] bge2 at pci10 dev 4 function 0: Broadcom BCM5714 Gigabit Ethernet [ 1.000000] bge2: interrupting at ivec 3796 [ 1.000000] bge2: HW config 00010115, 00000015, 00000000, 00000000 00000000 [ 1.000000] bge2: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:a2:38:cc [ 1.000000] bge2: autoconfiguration error: WARNING: failed to restrict dma range, falling back to parent bus dma range [ 1.000000] bge2: setting short Tx thresholds [ 1.000000] brgphy2 at bge2 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0 [ 1.000000] brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] bge3 at pci10 dev 4 function 1: Broadcom BCM5714 Gigabit Ethernet [ 1.000000] bge3: interrupting at ivec 3797 [ 1.000000] bge3: HW config 00000114, 00000014, 00000000, 00000000 00000000 [ 1.000000] bge3: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:a2:38:cd [ 1.000000] bge3: autoconfiguration error: WARNING: failed to restrict dma range, falling back to parent bus dma range [ 1.000000] bge3: setting short Tx thresholds [ 1.000000] brgphy3 at bge3 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0 [ 1.000000] brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto [ 1.000000] ppb10 at pci10 dev 8 function 0: ServerWorks HT1000 PCI/PCI-X Bridge (rev. 0xb4) [ 1.000000] pci11 at ppb10 bus 13 [ 1.000000] pci11: i/o space, memory space enabled [ 1.000000] mpt0 at pci11 dev 1 function 0: Symbios Logic SAS1064 (rev. 0x02) [ 1.000000] mpt0: interrupting at ivec 1f8f [ 1.000000] mpt0: Phy 0: Link Status Unknown [ 1.000000] mpt0: Phy 0: Link Status Unknown [ 1.000000] mpt0: Phy 0: Link Status Unknown [ 1.000000] mpt0: Phy 0: Link Status Unknown [ 1.000000] scsibus0 at mpt0: 63 targets, 8 luns per target [ 1.000000] pyro1 at mainbus0: "Fire", rev 3, ign 7c0, bus B 2 to 4 [ 1.000000] pyro1: pci12 at pyro1 [ 1.000000] pci12: i/o space, memory space enabled [ 1.000000] ppb11 at pci12 dev 0 function 0: Intel Serial to Parallel PCI Bridge A (rev. 0x09) [ 1.000000] ppb11: PCI Express capability version 1 [ 1.000000] pci13 at ppb11 bus 3 [ 1.000000] pci13: i/o space, memory space enabled [ 1.000000] ppb12 at pci12 dev 0 function 2: Intel Serial to Parallel PCI Bridge B (rev. 0x09) [ 1.000000] ppb12: PCI Express capability version 1 [ 1.000000] pci14 at ppb12 bus 4 [ 1.000000] pci14: i/o space, memory space enabled [ 1.000000] ebus1 at mainbus0 [ 1.000000] flashprom at ebus1 addr 0-1fffff not configured [ 1.000000] com0 at ebus1 addr 80-87 ipl 7c8: ns16550a, working fifo [ 1.000000] com0: console [ 1.000000] com1 at ebus1 addr 40-47 ipl 7c9: ns16550a, working fifo [ 1.000000] rmc-comm at ebus1 addr 0-7 ipl 7ca not configured [ 1.000000] gpio at ebus1 addr c0-c0 not configured [ 1.000000] env-monitor at ebus1 addr 0-80 not configured [ 1.000000] power at ebus1 addr 40-c1 ipl 7c3 not configured [ 1.000000] i2c at mainbus0 not configured [ 1.000000] pcons at mainbus0 not configured [ 1.000000] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0 [ 1.000003] timecounter: Timecounter "tick-counter" frequency 1504000000 Hz quality 100 [ 1.000003] timecounter: Timecounter "stick-counter" frequency 20000000 Hz quality 200 [ 1.000014] No counter-timer -- using %stick at 20MHz as system clock. [ 1.748376] scsibus0: waiting 2 seconds for devices to settle... [ 1.855854] uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1 [ 1.955853] uhub0: 3 ports with 3 removable, self powered [ 1.955853] uhub1 at usb1: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1 [ 2.062520] uhub1: 3 ports with 3 removable, self powered [ 2.065853] uhub2 at usb2: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1 [ 2.172517] uhub2: 8 ports with 8 removable, self powered [ 2.172517] atapibus0 at atabus0: 2 targets [ 2.225853] cd0 at atapibus0 drive 0: cdrom removable [ 2.325856] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) [ 2.325856] cd0(aceride0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA) [ 4.025853] sd0 at scsibus0 target 0 lun 0: disk fixed [ 4.155853] sd0: 70007 MB, 14100 cyl, 24 head, 423 sec, 512 bytes/sect x 143374738 sectors [ 4.255853] sd0: tagged queueing [ 4.297241] sd1 at scsibus0 target 1 lun 0: disk fixed [ 4.385853] sd1: 447 GB, 457863 cyl, 16 head, 127 sec, 512 bytes/sect x 937703088 sectors [ 4.485853] sd1: tagged queueing [ 4.545853] sd2 at scsibus0 target 2 lun 0: disk fixed [ 4.635853] sd2: 558 GB, 152800 cyl, 4 head, 1917 sec, 512 bytes/sect x 1172123568 sectors [ 4.735853] sd2: tagged queueing [ 4.785853] sd3 at scsibus0 target 3 lun 0: disk fixed [ 4.875853] sd3: 558 GB, 185281 cyl, 4 head, 1581 sec, 512 bytes/sect x 1172123568 sectors [ 4.975853] sd3: tagged queueing [ 5.175853] WARNING: 4 errors while detecting hardware; check system log. [ 5.255853] root on sd1a dumps on sd1b [ 5.305853] /: replaying log to memory [ 5.355853] root file system type: ffs [ 5.395853] kern.module.path=/stand/sparc64/9.2/modules [ 5.605855] uplcom0 at uhub0 port 1 [ 5.647817] uplcom0: Tripp-Lite (0x2478) U209 Serial adapter (0x2008), rev 1.10/a0.01, addr 2 [ 5.785854] ucom0 at uplcom0 [ 5.905856] /: replaying log to disk [ 6.985854] uhub3 at uhub1 port 1: Atmel (0x3eb) Standard USB Hub (0x3301), class 9/0, rev 1.10/3.00, addr 2 [ 7.125877] uhub3: 4 ports with 4 removable, self powered [ 7.445853] uplcom1 at uhub0 port 2 [ 7.485853] uplcom1: Prolific Technology Inc. (0x67b) USB-Serial Controller D (0x2303), rev 1.10/4.00, addr 3 [ 7.635853] ucom1 at uplcom1